rubbercrop4

How to Install a Ghost Immobiliser A ghost immobilise r is a hidden security system that shields your car from key cloning and hacking. It stops the engine from running until a PIN number is entered. This can be as long as 20 characters. It is undetectable by thieves and they are unlikely to think about this additional layer of security. Certain systems also come with an application that lets owners disarm the immobiliser in case they forget their PIN code or to switch to a service/valet mode. Connecting to the vehicle's CAN bus The Ghost 2 Immobiliser is an advanced security system that can be incorporated into your vehicle's ECU offering a secure security line against thieves. It is extremely efficient and user-friendly and is a great option to add to your vehicle's security arsenal. However, just like any other anti-theft system, it is not foolproof and requires regular maintenance to ensure its operation. Fortunately, this guide can assist you in getting the most benefit from your Ghost 2 Immobiliser. CAN (Controller Area Network), a robust serial networking system that lets microcontrollers communicate with each other over short distances. A central control unit is not required. It is designed to multiply electrical wiring in vehicles, thereby saving on copper. It offers many advantages, such as low cost and easy use. The CAN protocol is utilized in a majority of modern cars to communicate with the engine management system, steering control module, air conditioning controls, and more. It also carries sensor data including speed sensors and inputs to control various features of the vehicle. The CAN bus is used to monitor these various components, and it can stop a vehicle from starting if they are in danger of failure. It's important to know how the CAN bus works and how it is secured. It is possible to add new features to a vehicle by using CAN bus, however it's crucial to safeguard it against hackers and other threats. Installing a firewall, and monitoring your CAN-bus using software is the best way to do this. Ghost2's secluded control unit is hidden in the car's wiring harness or dashboard, which eliminates the possibility of a burglar physically altering it. It is also impossible to reset the PIN or emergency code without access to the vehicle. You can turn on Transport Mode If you need to sell your car for service, valet parking or any other reason. This feature disables the Ghost immobiliser's ignition and keyfob functions and will only reactivate when the vehicle reaches 31 mph for 15 minutes. The process of creating an PIN code The Ghost immobiliser shields your vehicle from thieves. The revolutionary technology utilizes an PIN to shut down the engine of your vehicle and prevent it from starting without the right code, or a valid fob/mobile. The system's subtle design ensures the system is unnoticeable and offers unparalleled protection against theft. The system is TASSA certified and could save you substantial sums on your car insurance. During the installation during installation, the Ghost system enters the learning mode to record the sequence of buttons pressed to generate your unique pin code. The installer will guide you through activating the system once the pin code is created. Once activated it will Ghost system will turn off the starter motor of your vehicle until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it very difficult for thieves to duplicate or hack your vehicle's starting system. Installing an Ghost immobiliser is easy but it is crucial to follow the detailed instructions in the user's guide to ensure proper operation. Hand tools are essential in making precise connections and a multimeter can assist in determining electrical values. Insulation tape and heat shrink tubing may protect exposed wiring, while cable tie-ups are crucial to keep everything tidy and secure. Be sure to check the system regularly to identify any issues or potential errors. Once the installation is complete, it is important to conduct a final test of the system prior to switching on the ignition of your vehicle. Ghost immobilisers are able to rearm themselves after 3 to 30 second depending on the model of your vehicle. The system is also equipped with a Service/Valet Mode that lets you temporarily disable the system to service or valet parking. Idealy, the immobiliser will be hidden under the dashboard or on the steering wheel. Make use of a small piece of duct tape or paint over the wires CAN H and L to make them easier to find when you are testing. The CAN H and the L wires should be connected to an electrical source that provides a constant 12V. It is also crucial to re-check the connections after testing, since misidentifying these wires can cause the system to malfunction. The system must be activated A ghost immobiliser blocks your car from starting when you press certain buttons inside the vehicle, typically on the steering wheel or door panel, or the central console. The sequence can be altered by the user in case it is needed. Once the system is activated it cannot be deactivated by thieves, making it a good option for anyone looking to protect their vehicle from theft. The system is designed to be undetectable, which means it cannot be detected by modern diagnostics or code-grabbing technologies. It also doesn't send out radio frequencies, which makes it even difficult for thieves to find the device. If the device is found it will stop the engine from starting. It will also sound an alarm to scare the thief away. The device can be used to track a car's location, which will help police recover the vehicle if it was taken. Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in Ghost immobiliser. We are fully certified to install a ghost immobiliser for your vehicle and will ensure it is hidden in a difficult-to-access area. We can also install additional security measures, including a kill switch and wheel lock to protect your vehicle from thieves. Disarming the System If you have an Ghost immobiliser that is fitted to your vehicle, it's essential to know how you can disable it. This will assist you in the case that you lock your keys in the car or your battery fails. The system is based on an individual PIN code that only you know, and the immobiliser will not start your vehicle without entering this code. The easiest way to enter the code is to press a set of buttons on your dashboard or the steering wheel. This is much simpler than using a key fob and stops others from copying your remote. Unlike some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and is compatible with your vehicle's bus network to operate. Its most distinctive characteristic is that it disables the engine, without affecting normal vehicle functions. This makes it very difficult for thieves to use signal boosts or to clone keys for cars. It does not emit radio frequency, so thieves cannot detect it. The Ghost system also has the Transport Mode that allows you to temporarily disable the security system for circumstances like transportation or servicing. This feature is useful if you are lending your vehicle to someone else without sharing your PIN number, or if your vehicle requires to be secured when you drive it. Press the service button five times in 2 seconds to activate the Transport Mode. The Ghost system will confirm activation via five indication signals. After you're done, make sure to save the emergency code in a secure place outside of your vehicle. If you are ever locked out of your vehicle You can call the company or technician who installed the system and they'll provide you with the code. If you are unable to reach them then you can try contacting an authorized dealer but this would require verification procedures and may incur additional charges. In addition to the convenience of this system, you can also count on it to guard your car against theft and reduce insurance costs. Many insurance companies offer lower rates or financial incentives to install this anti-theft system.